10' x 40' 45 Mil White TPO RV Rubber Roof Kit, membrane, adhesive, tape

Description

The Lottes Companies, Inc.
126 Point West Blvd
St. Charles, MO 63303
"More than 35 years of experience in single ply flat roofing products"
Most Orders Ship from Our Distribution Center in St. Charles, Missouri.
Professional White Rubber Roof: Complete Installation Kit 400 sq.ft.
First Rate Materials - WHITE 45 Mil TPO Rubber & Bonding Adhesive
Quality Products - Includes Membrane, Adhesive, Flashing Tape, and Caulk
Normally Shipped UPS Ground in Standard UPS Accepted Boxes and Weights
FREE DELIVERY in 48 States -
Included Items
1 - count 10' x 40' 45 Mil TPO WHITE Rubber Roofing Roll
1 - count  4 Gallon Pails Latex Bonding Adhesive
1 - count 1 Gallon Pail Latex Bonding Adhesive
1 - count 6" x 50' Uncured WHITE  tape Flashing
4 Tubes WHITE Lap Sealant Roofing Caulk
Light Weight only .27 lbs per square foot area
Twice the thickness, 45 mil, of the Super Flex Alpha Roof for longevity and lasting durability
20 year warranty on ALL residential, RV, motor homes and other types and sizes of installations
NOT INCLUDED Pictured Aluminum Termination bars, primer and Seam Tape NOT INCLUDED. Can be purchased separately
Why buy the NON-REINFORCED super thin product from our competitors when you  can have the highest quality TPO manufactured by the #1 TPO manufacturer in the United States, Johns Manville.
JM’s TPO roofing materials are formulated using the best available technology and designed for long-term roof performance in all conditions. We reinforce our TPO membrane with polyester fabric to provide excellent wind uplift resistance, puncture resistance and finished physical properties. And our TPO formulation was developed to allow for extreme pliability, flexibility and weldability during installation. Along with such installation advantages, our TPO’s state-of-the-art formulation helps our product to resist extreme weather conditions, including ultraviolet radiation and high surface temperatures
There is a edge seam guideline on one edge of the TPO sheet used for proper seam spacing and overlap if desired. If edge seam guide is not needed it can be easily trimmed off the one edge to leave a total clean and unmarked sheet.
R
ecommended
NOT to keep
the
TPO membrane in the shipping box for extended periods of time.
Highly Recommended to take the TPO membrane out of the shipping box as soon as possible and unroll and unfold to help the shipping creases relax and lay smooth.
Additional Information About our Quality TPO Rubber Membrane
Meets or exceeds ASTM D 6878 Roofing Certification and testing
Membrane is optimized and tested on a continual basis to verify the proper membrane thickness is supported
One of the widest melt windows  in the industry for TPO helping to insure a softer more pliable sheet.
Reinforced fabric scrim layer creating top level durable physical properties that include:
Long Term weathering, UV resistance and excellent heat aging properties
Very high breaking and shear tear strength
Optimized TPO formulations delivers highest performance ozone resistance, cool roof reflectivity and overall weather resistance
Method of Applying TPO with heavy bodied latex bonding adhesive and 3
”
seam tape application as required.
·
1
Clean the roof surface of all debris.. Re-fasten any loose roof boards.
·
2
Fill any gaps larger than 3/8” inch. The TPO cannot span gaps of more than 3/8" without risk of possible adhesion issues.
·
3
Start at the bottom of the roof and roll out the TPO from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane
·
4
Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Slowly fold the EPDM roofing membrane back into place while the adhesive is tacky and moist, and NOT still totally wet. This takes 10 to 15 minutes normally depending on your weather conditions. Please be aware NOT to lay the EPDM into WET adhesive but damp and tacky.
To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.
·
5
Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3” seam tape if required to splice 2 pieces of TPO deck sheet together.
·
6
Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.
Seam tape application if required to join 2 sheets together
• Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet.
• Clean and/or prime the seam area of both rubber sheets using Primer. CAUTION: wear protective gloves and read all labels and instructions when using Primer or unleaded gas to clean and prime the seam area
• Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2" out from the edges of the bottom sheet.
• Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam.
• With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape.
• Remove the paper backing by pulling out from under the top sheet at a 45º angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller.
Our Technicians can design and determine what you need for your roofing project and give you a complete estimate for your materials as well as instruct you about your installation process!
This Product is a Professional Grade Rubber Roof Installation Kit.
FREE DELIVERY IN 48 STATES
Flashing detail, seam flaps, & roof penetrations will determine actual roof coverage.  Please allow for these adjustments when purchasing materials.
Summary of Lottes Roofing Policies
Payment
All Credit Cards, Company Certified Checks, Bank Checks, , Bank Wire, Paypal
Fees
No sales taxes except in applicable states
Shipping
US and International
Delivery
24-48 hours to SHIP most in stock items, not counting weekends or holidays. Time tables will vary depending on the items ordered.
Refunds & Returns
Returns accepted on qualified items with RGA return number
Contact Us
BID WITH CONFIDENCE
Powered by
eBay Turbo Lister
The free listing tool. List your items fast and easy and manage your active items.
Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item
negotiated
between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items.
Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.
Contact us for Volume Discounts
Buy 3 items get 5% EXTRA Discount off items pricing
Buy 5 items get 8% EXTRA Discount off items pricing
We currently only ship to the lower 48 sates, not Alaska or Hawaii