EPDM Rubber Roof Roofing Kit COMPLETE - 500 sq.ft.

Description

Professional Rubber Roof: Complete Installation Kit - 500 sq.ft.
First Rate Materials - Black 45Mil EPDM Rubber & Latex Bonding Adhesive
Quality Products - Includes Seam Tape, Flashing Tape, Primer, Caulk, & T-Bars
Included Items
10' x 50' 45Mil EPDM Rubber Roofing Roll
1 count 4 Gallon Pails Latex Bonding Adhesive
3" x 25' Black Seam Tape
1 count 1 Gallon Can Seam Primer/Activator
6" x 25' Black Uncured EPDM Flashing Tape
10 count 10' x 1" Aluminum T-bars
2 Tubes Black Lap Sealant Roofing Caulk
Method of Applying EPDM with heavy bodied latex bonding adhesive and 3
”
seam tape application as required.
·
1
Clean the roof surface of all debris and nails. Re-fasten any loose roof boards.
·
2
Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8" without risk of possible adhesion issues.
·
3
Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane.
·
4
Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.
·
5
Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3” seam tape if required to splice 2 pieces of EPDM deck sheet together.
·
6
Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.
Seam tape application if required to join 2 sheets together
• Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet.
• Clean and/or prime the seam area of both rubber sheets using EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area
• Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2" out from the edges of the bottom sheet.
• Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam.
• With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape.
• Remove the paper backing by pulling out from under the top sheet at a 45º angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller.
Lottes Roofing
1853 C Sherman Dr. 4473
St. Charles, MO 63303
"More than 30 years of experience in single ply flat roofing products"
Most Orders Ship from Our Distribution Center in St. Charles, Missouri.
This Product is a Professional Grade EPDM Rubber Roof Installation Kit.
10' x 50' 45Mil EPDM Rubber Roofing Roll
1 count 4 Gallon Pails Latex Bonding Adhesive
3" x 50' Black Seam Tape
1 count 1 Gallon Can Seam Primer/Activator
6" x 25' Black EPDM Uncured Tape Flashing Tape
10 count 10' x 1" Aluminum T-bars Extruded 1/16"
2 Tubes Black Lap Sealant Roofing Caulk
Flashing detail, seam flaps, & roof penetrations will determine actual roof coverage.  Please allow for these adjustments when purchasing materials.
PLUS FREIGHT CHARGES
Summary of Lottes Roofing Store Policies
Payment
All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, Paypal
Fees
No sales taxes except in applicable states
Shipping
US and International
Delivery
24-48 hours to SHIP most in stock items, not counting weekends or holidays. Time tables will vary depending on the items ordered.
Refunds & Returns
Returns accepted on qualified items with RGA return number
Contact Us
SHOP WITH CONFIDENCE
Please be prepared to unload the product from the delivery vehicle. Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item
negotiated
between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items.