EPDM Rubber SEAMLESS Roofing Kit COMPLETE - 1,200 sq.ft. BY THE LOTTES COMPANIES

Description

Lottes Roofing
126 Point West Blvd
St. Charles, MO 63303
"More than 30 years of experience in single ply flat roofing products"
Most Orders Ship from Our Distribution Center in St. Charles, Missouri.
Professional Rubber Roof: Complete Installation Kit - 1,200 sq.ft.
First Rate Materials - Black 45Mil EPDM Rubber & Latex Bonding Adhesive
Quality Products - Includes ADHESIVE T-Bars
FREE SHIPPING 48 states
Included Items
1,200  sq ft. of 45 mil black EPDM, a SEAMLESS sheet 30' x 40'
3 count 4 Gallon Pails Latex Bonding Adhesive
14 count 10' x 1" Aluminum T-bars
Method of Applying EPDM with heavy bodied latex bonding adhesive
·
1
Clean the roof surface of all debris and nails. Re-fasten any loose roof boards.
·
2
Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8" without risk of possible adhesion issues.
·
3
Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane
·
4
Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Slowly fold the EPDM roofing membrane back into place while the adhesive is tacky and moist, and NOT still totally wet. This takes 10 to 15 minutes normally depending on your weather conditions. Please be aware NOT to lay the EPDM into WET adhesive but damp and tacky.
To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.
·
5
Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3” seam tape if required to splice 2 pieces of EPDM deck sheet together.
·
6
Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.
Structodek with Primed Red Coating
As an insulation board, coverboard or re-roof/recover board, Structodek High-Density Roofing Board is the answer for low-slope applications and systems.
STRUCTODEK INSULATION RECOVERY BOARD 4' X 8', 1/2" THICK 64 LBS PER SQUARE  3 - 4' X 8' BOARDS PER SQUARE (100 SQUARE FEET) NOTE 30.4 SQUARES CAN BE ON A  PALLET.
3 BOARDS 96 SQUARE FEET==95 PIECES PER PALLET===2,000 lbs per Pallet=729.6 SQUARES PER TRUCK, 24 PALLETS
.32 per 100 square feet,  MINIMUM QUANTITIES REQUIRED AT THIS PRICE LEVEL, 1 PALLET 30.4 SQUARES, 3,040 SQUARE FEET PER PALLET
++++=SOLD BY THE PALLET PLUS ++++++
STRUCTODEK® HIGH DENSITY (HD)
FIBERBOARD ROOF INSULATION
COVER BOARD WITH PRIMED RED COATING
DESCRIPTION
The proprietary, patent pending, non-asphaltic Primed Red Coating integrated on the surface of STRUCTODEK HD possesses unique bonding characteristics that ultimately result in superior adhesion capabilities with the current membrane & adhesive technology on the market today. The nonasphaltic Primed Red Coating is compatible with all single-ply membranes including PVC, TPO, EPDM, and CSPE without concern of premature membrane degradation that is often associated with asphalt emulsion coated fiberboard products.
Additionally the Primed Red Coating, unlike asphalt emulsion coated products, has proven to be compatible with traditional, low VOC and water-based adhesives as well as many foam adhesives. The Primed Red Coating allows adhesives & foams to “key” into the STRUCTODEK HD surface while at the same time deterring excessive adhesive absorption. The unique Primed Red Coating allows for a solid membrane bond while still providing optimal square foot per gallon of adhesive coverage thus insuring a quality & cost effective membrane installation.
This Product is a Professional Grade EPDM Rubber Roof Installation Kit.
Flashing detail, seam flaps, & roof penetrations will determine actual roof coverage.  Please allow for these adjustments when purchasing materials.
Summary of Lottes Roofing Store Policies
Payment
All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, Paypal
Fees
No sales taxes except in applicable states
Shipping
US and International
Delivery
24-48 hours to SHIP most in stock items, not counting weekends or holidays. Time tables will vary depending on the items ordered.
Refunds & Returns
Returns accepted on qualified items with RGA return number
Contact Us
SHOP WITH CONFIDENCE
Powered by
eBay Turbo Lister
The free listing tool. List your items fast and easy and manage your active items.
Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item
negotiated
between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items.
Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.
Contact us for Volume Discounts
Buy 3 items get 5% EXTRA Discount off items pricing
Buy 5 items get 8% EXTRA Discount off items pricing
We currently only ship to the lower 48 sates, not Alaska or Hawaii